Steps in Installing Drywall

How to Hang Drywall?

March 30, 2022 7 Read

Hanging drywall is a process that many homeowners will have to do at some point. Whether you are updating a room or repairing damage, hanging drywall is a necessary step. The process can seem daunting, but with the right tools and instructions, it is a manageable task.

The first step in hanging drywall is measuring the space you will be covering. This will help you determine how much drywall you need to purchase. Once you have the measurements, you can begin cutting the drywall panels to size. Make sure to use a sharp utility knife and be careful not to cut yourself.

The next step is attaching the drywall panels to the framing. You can do this with either screws or nails. If you are using screws, make sure to drill pilot holes first to avoid splitting the wood. Be sure to countersink the drywall screws so that they are flush with the surface of the drywall. If you are using nails, make sure they are slightly recessed so that they can be covered with joint compounds.

After the drywall is attached to the framing, it’s time to start taping the seams. You will need a joint compound and fiberglass mesh tape for this step. Drywall tape is self-adhesive tape that is used to cover the seams between panels of drywall. The joint compound is a mixture of plaster and water that is used to fill in the gaps between the panels and the tape.

There are several ways to apply the joint compound. For the door or window corner, it is best to use a 6-inch knife. For outside corners, an 8- or 10-inch drywall knife works best. For long seams, you can use a 12-inch knife. Window and door openings are best handled with a drywall saw.

After the joint compound has dried, it is time to sand it down. You can use a sanding sponge or an orbital sander for this step. Be sure to sand in the direction of the tape to avoid creating bumps.

If you have a pre existing drywall, make sure you check for any nails or screws that may have come loose. Tighten or replace them as needed. Inspect the drywall for any cracks or damage and repair as necessary.

Now that you know how to hang drywall, you can tackle this home improvement project with confidence. Remember to take your time and be careful when cutting and attaching the drywall. With a little patience and effort, you’ll have beautiful, new drywall in no time.

If you’re not confident in your abilities or if the project is too large, consider hiring a professional drywall installer. They will be able to get the job done quickly and efficiently.

Steps in Installing Drywall

Drywall is a versatile material that can be used for a variety of purposes, from creating walls to repairing existing ones. While it is possible to install drywall yourself, it’s generally best to hire a professional drywall contractor to do the job.

There are a few key steps involved to install drywall:

Measuring and Cutting the Drywall

The first step is to measure the space where the drywall will be installed and cut the panels to size. It’s important to make sure that the panels are the right size, as too much cutting can weaken them and make them more susceptible to damage. Drywall sheets are generally 4 feet wide and 8 feet long, so you’ll need to measure and mark the appropriate dimensions before cutting.

Every square foot of your exterior walls is made of approximately 32 square feet of drywall. So a wall that is 8-feet by 10-feet will require approximately 25 sheets of drywall. Drywall contractors typically charge between $1 and $2 per square foot, so this size wall would cost between $250 and $500 to install.

Installing the Drywall

Once the drywall is cut to size, the next step is to install it on the wall. This is generally done by attaching it to furring strips or studs with screws or nails. It’s important to make sure that the drywall is properly secured, as any movement can cause cracks or other damage. Moisture resistant panels should be used in areas where there is a high risk of moisture, such as bathrooms and kitchens. So, if you’re looking to install drywall in one of these areas, be sure to ask your contractor about the appropriate type of panel.

Tape and Mud the Drywall

Once the drywall is in place, it’s time to tape and mud it. Taping is the process of applying a layer of joint compound over the seams between panels. This helps to create a smooth, even surface that can be painted or papered over. Mud is a type of joint compound that is used for this purpose. Once the seams are taped, the entire surface of the drywall should be covered with a thin layer of mud. This is known as mudding.

Also, a texture drywall compound can be applied with a drywall knife over the entire surface to give it a finished look. All the drywall screws or nails should be filled with drywall compound and sanded smooth. If screw heads are visible, they can be covered with a wood plug or dowel.


After the mud has had time to dry, it’s time to sand it. This helps to create an even surface and can make all the difference in the final product. Use a pole sander for larger areas and a hand sander for smaller, more delicate areas. Be sure to use fine-grit sandpaper so you don’t damage the drywall. Fasten panels to furring strips with drywall screws. Use a power drill to make the job go faster.

Fire-resistant panels like gypsum board is a perfect material for walls and ceilings in homes. It resists the spread of fire, insulates well, and can help reduce sound transmission. Also, a completely covered wall or ceiling is easier to paint than an exposed stud wall.

Applying Tape

After the mud is smooth, it’s time to apply tape to the seams. Start by tearing off a length of tape and gently pressing it into the mud, being careful not to press too hard and create an indentation. Once the tape is in place, use your knife to lightly score along the edge of the tape, being careful not to cut through it. This will help the mud adhere to the tape and form a watertight seal. Excess compound can be trimmed away with your knife.

Applying Second Coat of Mud

Once the tape is dry, you can apply a second coat of mud. Be sure to use a trowel that’s the same width as the tape to avoid creating any unevenness in the surface. Apply the mud in thin layers, feathering it out as you go. Let the mud dry completely before sanding it. However, curved walls may require a third coat of mud. Exposed timber also needs special treatment and may need a coat of primer before you start plastering.

And if you remove wood paneling, make sure to remove all the nails and secure any sharp edges before starting to work.

Sanding and Touching Up

After the mud has dried, use a sandpaper block to smooth out any bumps or ridges. Be careful not to sand through the paper tape. If you do, apply a new coat of mud and let it dry. Once the mud is completely dry, use fine-grit sandpaper to sand the entire surface until it’s smooth.

If you notice any areas where the paint has chipped or is starting to peel, touch them up with a matching paint color. Let the paint dry completely before moving on to the next step.

Finishing drywall is a process that can be accomplished by following a few simple steps. The first step in finishing drywall is to tape the seams between the panels. Taping the seams will help to ensure that the finished wall is smooth and free of any bumps or ridges. The next step is to apply mud to the seams and sand them until they are smooth. After the seams have been mudded and sanded, it is time to apply the finish coat. The finish coat can be applied using a roller or a brush. Finally, it is important to allow the drywall to dry completely before painting or wallpapering.

Take Away

Drywall installation is a process that can be accomplished by following a few simple steps. All the steps mentioned above are just a guideline, so always be sure to consult the drywall installation instructions that come with your drywall. If you’re having trouble following the instructions, or have any other questions about drywall installation, don’t hesitate to call a professional drywall installer. Drywall installation cost will depend on the size of your project, but it’s typically a fairly inexpensive home improvement project.